[Q16-Q36] Pass Your CCNP Data Center 300-615 Exam Easily with Accurate PDF Questions [Apr 19, 2022]

Rate this post

Pass Your CCNP Data Center 300-615 Exam Easily with Accurate PDF Questions [Apr 19, 2022]

300-615 Certification Exam Dumps Questions in here

NO.16

Refer to the exhibit. The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID
0x970200. Which action resolves the issue?

Reconfigure the initiator and the target to be in the same zones.

Reactivate the zoneset.

Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.

Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.

Section: Storage Network

NO.17 Refer to the exhibit.

Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.

NO.18 An engineer attempts to register Cisco UCS Manager to Cisco UCS Central, but the registration fails. The engineer can ping Cisco UCS Central from UCS Manager. Which two actions must the engineer attempt to resolve the problem? (Choose two.)

Synchronize the date and time to NTP for Cisco UCS Central and the Cisco UCS domains.

Apply the UCS Central license to UCS Central.

Place Cisco UCS Manager on the same subnet as Cisco UCS Central.

Allow port 443 between Cisco UCS Manager and Cisco UCS Central.

Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

Section: Compute Platforms

NO.19 One of Cisco Nexus Series interfaces has become errdisabled with the error message “DCX-No ACK in
100 PDUs”. What is the cause of this error?

The host has not responded to the Control Sub-TLV DCBX exchanges of the switch.

The acknowledgement number in the server response has not incremented for 100 exchanges.

Cisco Discovery Protocol is disabled on the switch.

LLDP is disabled on the switch.

Section: Storage Network

NO.20 An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.

NO.21

Refer to the exhibit. The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?

Reconfigure the initiator and the target to be in the same zones.

Reactivate the zoneset.

Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.

Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.

Section: Storage Network

NO.22 A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?

Set the same WWPN pools for vHBA adapters

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the same WWNN pools for vHBA adaptor

NO.23 Refer to the exhibit.

A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?

event cli match ‘configure terminal’

event policy-default count 1 time 100

event syslog occurs 10

action 2.0 event-default

NO.24

Refer to the exhibit. An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount. Which action resolves the issue?

Statically configure the target information in the Boot Policy.

Configure an MTU size of 9000 on the appliance port.

Configure a QoS policy on the vNIC.

Set a connection timeout value of 250 in the iSCSI Adapter Policy.

Section: Compute Platforms

NO.25

Refer to the exhibit. The EEM script fails to send an SNMP trap when a user attempts to enter configuration mode. Which configuration is missing from the script?

event statement

event-default action statement

policy-default action statement

IP address of the SNMP server

Section: Automation

NO.26 Refer to the exhibit.

A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?

event cli match ‘configure terminal’

event policy-default count 1 time 100

event syslog occurs 10

action 2.0 event-default

NO.27 Refer to the exhibit.

The HSRP instance on both switches is showing as active. Which action resolves the issue?

Configure the HSRP timers to be the same.

Allow VLAN 100 between the switches.

Configure the IP address of N9K-B on the same subnet as N9K-A.

Configure preempt on only one of the switches.

NO.28 A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?

Set the same WWPN pools for vHBA adapters

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the same WWNN pools for vHBA adaptor

NO.29 A customer configures HSRP between two data centers that are interconnected with OTV. The configuration succeeds, but traffic between two ESXi virtual hosts on the same site is routed suboptimally through the OTV overlay. Which two actions optimize the traffic? (Choose two.)

Disable first-hop redundancy.

Filter HSRP traffic by using a Layer 3 VACL on the OTV edge devices.

Filter HSRP by using a Layer 2 MAC-list on the ESXi vSwitch.

Filter HSRP traffic by using a Layer 3 VACL on the ESXi vSwitch.

Filter HSRP by using a Layer 2 MAC-list on the OTV edge devices.

Section: Network

NO.30 Drag and drop the commands from the left onto the correct categories on the right.

NO.31 Refer to the exhibit.

A network engineer traces the packet flow from the Veth991 of a blade server toward the core switch. The switch reports performance issues What is the role of the interface Eth1/7?

IOM network interface

fabric interconnect uplink interface

IOM host interface

server interface

Explanation
E1/7 is border interface, which is used as uplink. All other veth interfaces are SIF, which stands for Server Interface.

NO.32 Refer to the exhibit.

An engineer must connect N2K-Fex-1 and N5K-Core-1 so that the traffic flow between the two devices uses load balancing. After inspecting the statistics of the interconnecting interfaces, the engineer concludes that only one link is used. Which action resolves the problem?

Configure source-destination load balancing on N5K-Core-1.

Configure each uplink to be a member of a separate LACP port channel.

Configure the pinning max-link as 2.

Configure destination-mac load balancing on N5K-Core-1

Explanation
https://www.cisco.com/c/m/en_us/techdoc/dc/reference/cli/n5k/commands/pinning-max-links.html

NO.33 Refer to the exhibit.

The integration between Cisco UCS Manager and Cisco UCS Central failed. Which action resolves the issue?

Implement the consistent NTP source between the appliances

Implement the connectivity between the appliances through a firewall

Configure the certificate between the appliances

Configure the shared secret key between the appliances

NO.34 Refer to the exhibit.

An engineer configures the server port on a Cisco Nexus 5000 Series Switch. The switch connects to an NPV edge switch port. The server fails to send the FC traffic to the fabric. Which action resolves the issue?

Enable the NPIV mode on the Cisco Nexus 5000 switch.

Match the VSAN membership on both ends of the connection.

Configure the BB_credit buffer on the uplink port.

Replace the SFP in slot fc2/12.

NO.35 Refer to the exhibit.

A network administrator must delete a feature group from a Cisco Nexus 5000 Series Switch. Which action resolves the issue?

Detach the association with the no rule command within the role configuration mode

Detach the association with the no role command within the feature-group configuration mode

Detach the association with the no rule command within the feature-group configuration

Detach the association with the no role command within the role configuration mode

NO.36 Drag and drop the commands from the left onto the correct categories on the right.

Loading …

Introduction to Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Exam

The Troubleshooting Cisco Data Center Infrastructure (DCIT) v7.0 course shows you how to troubleshoot LAN, SAN, Cisco Data Center Unified Fabric, Cisco Unified Computing System (Cisco UCS), and Cisco Application-Centric Infrastructure (Cisco ACI). You will learn methodologies and tools to identify issues that may occur in data center network architecture. You will get extensive hands-on practice troubleshooting installation, configuration, and interconnectivity issues on Cisco Multilayer Director Switch (MDS) switches, Cisco Nexus® switches, Cisco Fabric Extenders (FEXs).

Updated 300-615 Exam Practice Test Questions: https://www.actualtests4sure.com/300-615-test-questions.html