[May 29, 2022] Reliable NACE-CIP2-001 Exam Tips Test Pdf Exam Material [Q34-Q51] : Actual Test Materials : http://blog.actualtests4sure.com

NEW QUESTION 34
The best choice of instrument for holiday testing of thick film concrete coatings is:

Low Voltage Sponge Type

High Voltage DC Pulse Type

High Voltage DC Constant Current

High Voltage AC

NEW QUESTION 35
Surface preparation methods for Non-ferrous metals are:

The same as for Ferrous metals

The same for all Non-FetT0us metals

Specific for each type of Non-ferrous metal

Not required

NEW QUESTION 36
When environmental enclosures are being used an inspector needs to be concerned about:

Lighting

Air changes

Structural integrity

a), b), and c)

NEW QUESTION 37
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:

Different than air blast cleaning

The same as air blast cleaning

Slightly different to air blast cleaning

Comparable to air blast cleaning

NEW QUESTION 38
It is always possible to see moisture on a steel substrate:

True

False

NEW QUESTION 39
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)

True

False

NEW QUESTION 40
An Inspection and Test Plan is required when:

It is always required

When the Coating Applicator requests one

When the Owner specifies one

When the Inspector requests one

NEW QUESTION 41
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:

Refuse to take readings until an is in place

Develop your own methodology and proceed take the readings

Use a generally accepted industry standard and to take readings

Call your supervisor

NEW QUESTION 42
You should bulk store coatings containing isocyanates

in a well ventilated area separate from the work place.

in a heated warehouse.

in a refrigerated warehouses

wherever it is convenient

NEW QUESTION 43
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:

Power Tools

Abrasive Blasting Equipment

Water Jetting Equipment

Scarifiers

NEW QUESTION 44
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?

Flow stage

Wetting stage

Cure stage

Gel stage

NEW QUESTION 45
The number of air turns in an enclosure can be affected by all of these EXCEPT

time of the year (winter/summer).

type of dehumidification equipment (refrigerant or desiccant).

manufacturer of the equipment.

coating type.

NEW QUESTION 46
You can use magnifiers to examine all of the following EXCEPT

Surface profile

Surface cleanliness

Blisters

Mill scale

NEW QUESTION 47
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:

Investigate to find the source of the odor

Don your air supplied respirator and continue the testing

Exit the tank and immediately and report the problem to the nearest safety supervisor

Exit the tank and document the incident in your daily report

NEW QUESTION 48
Antifouling coatings are regulated by international treaties.

True

False

NEW QUESTION 49
NACE No.13/ SSPC 6 identifies the use of:

Abrasive blasting only

Watterjetting only

Steam cleaning only

Various methods of cleaning

NEW QUESTION 50
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires

25 single rubs with a saturated cloth.

35 single rubs with a saturated cloth.

50 double rubs with a saturated cloth.

25 double rubs with a saturated cloth.

NEW QUESTION 51
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:

Correct the errors yourself and suggest the Level 1 inspector be replaced

Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent

Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation

Correct the errors yourself and submit the reports without any further action