This page was exported from Actual Test Materials [ http://blog.actualtests4sure.com ] Export date:Wed Jan 22 7:05:21 2025 / +0000 GMT ___________________________________________________ Title: Pass VMware 2V0-41.24 Exam With Practice Test Questions Dumps Bundle [Q22-Q40] --------------------------------------------------- Pass VMware 2V0-41.24 Exam With Practice Test Questions Dumps Bundle 2025 Valid 2V0-41.24 test answers & VMware Exam PDF VMware 2V0-41.24 Exam Syllabus Topics: TopicDetailsTopic 1Troubleshoot and Optimize the VMware Solution: This section evaluates the skills of VMware Networking Professionals in troubleshooting and optimizing NSX solutions. Candidates will use log files to identify issues, including locating default log file locations and generating log bundles to assist in diagnostics.Topic 2Install, Configure, and Administrate the VMware Solution: This domain targets VMware System administrators and emphasizes preparing an NSX infrastructure for deployment. Candidates will learn to create transport zones and configure essential components necessary for a functional NSX environment.Topic 3VMware Solution: This section measures the skills of VMware NSX Networking professionals and covers knowledge of the VMware Virtual Cloud Network and NSX. Candidates will demonstrate an understanding of the NSX management cluster and the data plane, focusing on how these components interact to provide network virtualization.   NEW QUESTION 22An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time.Which CLI command disables the nsxcli time out value on NSX Manager?  set cli-timeout 1  set cli-timeout enabled  set cli-timeout disabled  set cli-timeout 0 Setting the cli-timeout value to 0 disables the CLI timeout on NSX Manager, preventing the nsxcli session from timing out due to inactivity. This ensures that the session remains active indefinitely until manually closed.NEW QUESTION 23What must be configured on Transport Nodes for encapsulation and decapsulation of Geneve protocol?  VXIAN  UDP  STT  TEP According to the VMware NSX Documentation, TEP stands for Tunnel End Point and is a logical interface that must be configured on transport nodes for encapsulation and decapsulation of Geneve protocol. Geneve is a tunneling protocol that encapsulates the original packet with an outer header that contains metadata such as the virtual network identifier (VNI) and the transport node IP address. TEPs are responsible for adding and removing the Geneve header as the packet traverses the overlay network.NEW QUESTION 24Which two statements describe the characteristics of an Edge Cluster in NSX? (Choose two.)  Can have a maximum of 10 edge nodes  Can have a maximum of 8 edge nodes  Can contain multiple types of edge nodes (VM or bare metal)  Must contain only one type of edge nodes (VM or bare metal)  Must have only active-active edge nodes Reference:https://configmax.vmware.com/guest?vmwareproduct=NSX-T%20Data%20Center&release=NSX- T%20Data%20Center%203.0.0&categories=17-0https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/installation/GUID-14183A62-8E8D-43CC-92E0-E8D72E198D5A.htmlNEW QUESTION 25An administrator needs to download the support bundle for NSX Manager.Where does the administrator download the log bundle from?  System > Utilities > Tools  System > Support Bundle  System > Settings > Support Bundle  System > Settings https://docs.vmware.com/en/VMware-NSX/4.1/nsx-application-platform/GUID-50FB1A3F-07D8-4125-9252-DB05C28BE7E1.html: Procedure From your browser, log in with Enterprise Admin privileges to an NSX Manager at https://<nsx-manager-ip-address>. Navigate to System > Support Bundle. In the Request Bundle tab, select NSX Application Platform from the Type drop-down menu.NEW QUESTION 26Which two statements are correct about East-West Malware Prevention? (Choose two.)  A SVM is deployed on every ESXi host.  NSX Application Platform must have Internet access.  An agent must be installed on every ESXi host.  An agent must be installed on every NSX Edge node.  NSX Edge nodes must have Internet access. Reference: https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.2/administration/GUID-0A8BF7D8-9C2E-48A5-8219-17C00F1EC13A.html https://www.wwt.com/blog/primer-series-napp-malware-preventionNEW QUESTION 27Which three of the following describe the Border Gateway Routing Protocol (BGP) configuration on a Tier-0 Gateway? (Choose three.)  Can be used as an Exterior Gateway Protocol.  It supports a 4-byte autonomous system number.  The network is divided into areas that are logical groups.  EIGRP Is disabled by default.  BGP is enabled by default. A) Can be used as an Exterior Gateway Protocol. This is correct. BGP is a protocol that can be used to exchange routing information between different autonomous systems (AS). An AS is a network or a group of networks under a single administrative control. BGP can be used as an Exterior Gateway Protocol (EGP) to connect an AS to other ASes on the internet or other external networks1 B) It supports a 4-byte autonomous system number. This is correct. BGP supports both 2-byte and 4- byte AS numbers. A 2-byte AS number can range from 1 to 65535, while a 4-byte AS number can range from 65536 to 4294967295. NSX supports both 2-byte and 4-byte AS numbers for BGP configuration on a Tier-0 Gateway2 C) The network is divided into areas that are logical groups. This is incorrect. This statement describes OSPF, not BGP. OSPF is another routing protocol that operates within a single AS and divides the network into areas to reduce routing overhead and improve scalability. BGP does not use the concept of areas, but rather uses attributes, policies, and filters to control the routing decisions and traffic flow3 D) FIGRP Is disabled by default. This is correct. FIGRP stands for Fast Interior Gateway Routing Protocol, which is an enhanced version of IGRP, an obsolete routing protocol developed by Cisco.FIGRP is not supported by NSX and is disabled by default on a Tier-0 Gateway.E) BGP is enabled by default. This is incorrect. BGP is not enabled by default on a Tier-0 Gateway. To enable BGP, you need to configure the local AS number and the BGP neighbors on the Tier-0 Gateway using the NSX Manager UI or API.To learn more about BGP configuration on a Tier-0 Gateway in NSX, you can refer to the following resources:VMware NSX Documentation: Configure BGP 1VMware NSX 4.x Professional: BGP ConfigurationVMware NSX 4.x Professional: BGP TroubleshootingNEW QUESTION 28Which two of the following will be used for ingress traffic on the Edge node supporting a Single Tier topology? (Choose two.)  Tier-1 SR Router Port  Tier-0 Uplink interface  Downlink Interface for the Tier-0 DR  Downlink Interface for the Tier-1 DR  Inter-Tier interface on the Tier-0 gateway Tier-1 SR Router Port: This port is used for ingress traffic on the Tier-1 Service Router (SR), which handles traffic as it enters the Tier-1 gateway.Tier-1 SR Router Port: This port is used for ingress traffic on the Tier-1 Service Router (SR), which handles traffic as it enters the Tier-1 gateway.NEW QUESTION 29HOTSPOTRefer to the exhibit.Which two items must be configured to enable OSPF for the Tler-0 Gateway in the Image? Mark your answers by clicking twice on the image. Explanation:The correct answer is to enable the OSPF toggle and to add an Area Definition for the Tier-0 gateway in the image. These two items are required to configure OSPF on the Tier-0 gateway, as explained in the web search results123.To mark your answers by clicking twice on the image, you can double-click on the toggle switch next to OSPF to turn it on. The switch should change from gray to blue, indicating that the option is enabled.Then, you can double-click on the Set button next to Area Definition to add an area definition. A pop-up window should appear where you can specify the area ID and type.1. Click the OSPF toggle to enable OSPF 2. In the Area Definition field, click Set to add an area definition https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.2/administration/GUID-5BEC626C-5312-467D-B873-8E117349E9FC.htmlNEW QUESTION 30Match the NSX Intelligence recommendations with their correct purpose. NEW QUESTION 31Which two commands does an NSX administrator use to check the IP address of the VMkernel port for the Geneve protocol on the ESXi transport node? (Choose two.)  net-dvs  esxcfg-nics -l  esxcli network ip interface ipv4 get  esxcfg-vmknic -l  esxcli network nic list The esxcli network ip interface ipv4 get command is used to display the IP address configuration of the VMkernel network interfaces, including those used for the Geneve protocol.The esxcfg-vmknic -l command lists all VMkernel network interfaces, including their IP addresses, which can help identify the VMkernel port for the Geneve protocol.NEW QUESTION 32Which NSX CLI command is used to change the authentication policy for local users?  Set cli-timeout  Get auth-policy minimum-password-length  Set hardening- policy  Set auth-policy According to the VMware NSX Documentation4, the set auth-policy command is used to change the authentication policy settings for local users, such as password length, lockout period, and maximum authentication failures. The other commands are either used to view the authentication policy settings (B), change the CLI session timeout (A), or change the hardening policy settings .Reference: 4: Authentication Policy Settings – VMware Docshttps://docs.vmware.com/en/VMware-NSX/4.1/administration/GUID-99BAED85-D754-4589-9050-72A1AB528C10.htmlNEW QUESTION 33Which of the following settings must be configured in an NSX environment before enabling stateful active-active SNAT?  Tier-1 gateway in active-standby mode  Tier-1 gateway in distributed only mode  An Interface Group for the NSX Edge uplinks  A Punting Traffic Group for the NSX Edge uplinks To enable stateful active-active SNAT on a Tier-0 or Tier-1 gateway, you must configure an Interface Group for the NSX Edge uplinks. An Interface Group is a logical grouping of NSX Edge interfaces that belong to the same failure domain. A failure domain is a set of NSX Edge nodes that share the same physical network infrastructure and are subject to the same network failures. By configuring an Interface Group, you can ensure that the stateful services are distributed across different failure domains and can recover from network failures1NEW QUESTION 34Which table on an ESXi host is used to determine the location of a particular workload for a frame-forwarding decision?  Routing Table  ARP Table  TEP Table  MAC Table The MAC Table on an ESXi host is used to determine the location of a particular workload for frame-forwarding decisions. This table maps MAC addresses to specific interfaces, enabling the ESXi host to forward frames to the correct destination based on the MAC address of the workload. This is crucial for efficient Layer 2 forwarding decisions within the host.NEW QUESTION 35A company security policy requires all users to log into applications using a centralized authentication system.Which two authentication, authorization, and accounting (AAA) systems are available when integrating NSX with VMware Identity Manager? (Choose two.)  RSA SecureID  SecureDAP  RADII 2.0  LDAP and OpenLDAP based on Active Directory (AD)  Keygen Enterprise RSA SecureID: RSA SecureID is a commonly used two-factor authentication (2FA) system that can integrate with VMware Identity Manager for enhanced security during authentication, making it a suitable AAA system for user authentication.LDAP and OpenLDAP based on Active Directory (AD): VMware Identity Manager can integrate with LDAP and OpenLDAP directories, including Active Directory (AD), for centralized user authentication. This allows users to authenticate against an organization’s directory service.NEW QUESTION 36An NSX administrator has deployed a single NSX Manager node and will be adding two additional nodes to form a 3-node NSX Management Cluster for a production environment. The administrator will deploy these two additional nodes and Cluster VIP using the NSX UI.What two are the prerequisites for this configuration? (Choose two.)  All nodes must be in separate subnets.  The cluster configuration must be completed using API.  NSX Manager must reside on a Windows Server.  All nodes must be in the same subnet.  A compute manager must be configured. According to the VMware NSX Documentation, these are the prerequisites for adding nodes to an NSX Management Cluster using the NSX UI:All nodes must be in the same subnet and have IP connectivity with each other.A compute manager must be configured and associated with the NSX Manager node.The NSX Manager node must have a valid license.The NSX Manager node must have a valid certificate.NEW QUESTION 37Which command on ESXi is used to verify the Local Control Plane connectivity with Central Control Plane?  esxcli network ip connection list | grep netcpa  esxcli network ip connection list | grep ccpd  esxcli network ip connection list | grep 1234  esxcli network ip connection list | grep 1235 The netcpa process is responsible for Local Control Plane (LCP) connectivity with the Central Control Plane (CCP) in NSX. Using the command esxcli network ip connection list | grep netcpa, administrators can verify the connectivity status between the LCP on the ESXi host and the CCP, ensuring proper communication for NSX operations.NEW QUESTION 38What are two supported host switch modes? (Choose two.)  Overlay Datapath  Secure Datapath  Standard Datapath  Enhanced Datapath  DPDK Datapath Standard Datapath: This is the traditional mode used by the NSX host switch. It is typically used in environments where performance requirements are standard and no special acceleration techniques are needed.Enhanced Datapath: This mode is designed to improve performance and provide better scalability, especially for environments with higher traffic loads or more demanding applications. It can provide better performance in certain scenarios by improving packet processing efficiency.NEW QUESTION 39As part of an organization’s IT security compliance requirement, NSX Manager must be configured for 2FA (two-factor authentication).What should an NSX administrator have ready before the integration can be configured? O  Active Directory LDAP integration with OAuth Client added  VMware Identity Manager with an OAuth Client added  Active Directory LDAP integration with ADFS  VMware Identity Manager with NSX added as a Web Application To configure NSX Manager for two-factor authentication (2FA), an NSX administrator must have VMware Identity Manager (vIDM) with an OAuth Client added. vIDM provides identity management services and supports various 2FA methods, such as VMware Verify, RSA SecurID, and RADIUS. An OAuth Client is a configuration entity in vIDM that represents an application that can use vIDM for authentication and authorization. NSX Manager must be registered as an OAuth Client in vIDM before it can use 2FA.Reference: : VMware NSX-T Data Center Installation Guide, page 19. : VMware NSX-T Data Center Administration Guide, page 102. : VMware Blogs: Two-Factor Authentication with VMware NSX-TNEW QUESTION 40Match the NSX Intelligence recommendations with their correct purpose.  Loading … Top VMware 2V0-41.24 Courses Online: https://www.actualtests4sure.com/2V0-41.24-test-questions.html --------------------------------------------------- Images: https://blog.actualtests4sure.com/wp-content/plugins/watu/loading.gif https://blog.actualtests4sure.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2025-01-05 10:59:11 Post date GMT: 2025-01-05 10:59:11 Post modified date: 2025-01-05 10:59:11 Post modified date GMT: 2025-01-05 10:59:11